Sometimes it happens that you have to increase the size of the ring. The reason for this action may be due to the wrong choice of the size of the jewelry. Perhaps someone simply did not know the size and could not find the right ring. It happens that the hand has recovered or, conversely, at the time of purchase it was swollen, swollen, and then lost weight. But is it difficult to fit the product in size? And what is the best way to do it?
Easy and safe bore option
It is quite possible to increase the size of a ring with a stone in the simplest and safest way - through boring the product. This procedure involves sawing out the inner layer of the shank. It allows you to enlarge your ring by about half the size. The method is ideal for decorative and precious stones with a wide shank.
The process is usually performed using a special machine with a lock. It is not suitable for rings that are too thin. Only for wide. Takes approximately 10-30 minutes. However, this method has its downsides. Due to the use of rolling or boring, the thickness of the shank will decrease. It will become thinner than its original thickness.
Increase the size by rolling
There is another simple option that allows you to increase the size of a wedding ring or any other product. It means rolling metal. It is performed using special equipment, a machine. As in the case of boring, it is necessary to narrow the shank of the ring. In this case, it will also become narrower, and the size of the ring will increase.
Metal inserts
To increase the size of the ring, you can use inserts made of a suitable metal. In the process of work, the master carefully cuts the shank from below (in the place where it touches the finger). And then he begins to push it as far as it will be necessary to increase the decoration in size. For example, if you need to increase the product by one size, you need to expand it by about 3.14 mm.
The resulting space is covered with a small piece of metal, completely suitable in terms of parameters and appearance to the ring itself. At the same time, the joints are treated not only with a laser, but also with fire. To give the decoration a natural shine, it is necessary to immerse it in a solution with boric acid. After that, you won’t even be able to distinguish where the original metal patch is located, and where the factory shank begins.
The type of soldering directly depends on the existing shape of the stone on the product. Increasethe size of the ring by soldering an insert from an identical metal can be done in at least an hour. Sometimes it takes more time to process the product.
Using the Pinocchio tool
To increase the size of a piece of jewelry, an apparatus called "Pinocchio" is often used. During the procedure, they usually put a ring on it and begin to stretch it due to an increase in the size of the cone. However, before increasing the size of the ring with Pinocchio, it is necessary to heat the product. Otherwise, you risk tearing the jewelry or deforming it.
According to experts, this option is perfect for working with wedding rings and products of the most ordinary rounded shape. On average, such work does not take more than 25-30 minutes.
Application of mechanical stretching of metal
Answering the question of whether it is possible to increase the size of the ring, one cannot but recall the method of mechanical stretching of the metal. However, the method is not suitable for products with complex decorative patterns. The presence of a small stone in this case is allowed. The ring itself should also not be too wide. Its approximate thickness should not be more than 10 mm.
In the process of work, the master usually performs calculations, determines the size. After that, he rotates the fixed decoration on a special crossbar and heats it up. Thus, he manages to achieve suitable dimensions of the product. At the end of the procedure, it is necessary to eliminate roughness and uneven areas of the tavern. To do this, it is cleanedand polished.
Making a metal insert without sawing out
In the course of work, the master uses an additional metal plate made of a similar metal. Or instead of it, he uses an additional ring inserted inside your product. This method, according to jewelers, is considered the most expensive. However, it does not have any physical effect on the main decoration. All resizing work is carried out with the used internal inserts. As a result, it is not the ring itself that changes, but its inner diameter.
How to increase the ring size at home
Changing the size of a product is not as easy as it might seem at first glance. Therefore, in most cases, experts recommend not even trying. There is a huge risk that you will spoil the product. In such cases, it is best to contact specialists.
However, if you are still determined, you will need the following tools for the job:
- Special bolt.
- Gas burner.
- Small rubber mallet.
But keep in mind that having all these tools does not give any guarantee that you will succeed. First you need to take the ring and clamp it, for example, in pliers or round nose pliers. Then you need to turn on the burner and heat the product to a characteristic red color. Next, leave the decoration for a few minutes to cool down a bit. And when it is slightly warm, it remains to insert it into the crossbar and startrolling.
What products can be rolled out
Before rolling, please note that not all products can be processed in this way. For example, you cannot use rolling for rings with rotating inserts. You should not try this method for bimetallic products. It is not recommended to roll out even in the presence of inscriptions, engravings and drawings.
If your rings contain stones, carefully remove them before performing the procedure. Otherwise, when the ring is stretched, they may leave their “nests” and jump out. At the end of the work, you can return the stones back and fix them securely using round nose pliers, for example.
Be careful
Be careful! Lest the expression "The miser pays twice" apply to you, do not save. If you have a product that is not suitable in size, but is very expensive for you, give it to professionals. Let the work cost money, but it will keep the look of your jewelry.